Dartboard regulation

A complete guide about dartboard regulation

person hqt
date Jun 23, 2022

If you've never did dartboard regulation before, it might be a bit challenging. You must know not just the exact dartboard height, but also the throw line distance from the dartboard, which can be measured horizontally or diagonally and differs between electronic and steel tip dartboards. Fortunately, installing your dartboard and gauging throwing darts distance is simple and quick with the appropriate instructions. In no time, you'll have your dartboard set up to play dart games like 01 and Cricket if you follow the simple instructions below. Dartboard Dimensions Official Dartboard Dimensions

Whether you have a traditional steel tip dartboard or an electronic dartboard, the diagrams below will show you how to set up your dartboard. From the bullseye to the floor, the correct dart board height is 5' 8". Regardless of the sort of dart board you have, this measurement is the same. The throwline can be measured horizontally or diagonally, depending on which is more convenient for you and your instruments. Dartboard Height The standard dartboard height is 5 feet 8 inches from the floor to the center of the bullseye (1.73 meters). This dimension is universally accepted and applies to both electronic and steel tip dartboards.

We suggest that you measure and mount the dartboard first. We recommend that you measure and mount the dartboard before determining the throw line distance. Horizontal Dartboard Distance for Throw Line. Steel tip and soft tip dartboards have different horizontal distances from the face of the dartboard to the front of the throwline. Dartboards with steel tips have a horizontal distance of 7 feet 9 14 inches (2.37 meters). Dartboards with soft tips have an 8-foot horizontal distance (2.44 meters). It's crucial to take your measurements from the dartboard's face rather than the wall. You may calculate the depth of your dartboard regulation by multiplying it by the horizontal distance from the wall. You may also drop a thread from the dartboard's face to the ground and measure from there. In any case, you'll have the same outcome.

Dartboard Pitch Lines Length - Horizontal

Another method for determining throw line distance is to take a diagonal measurement. The distance varies depending on the type of dartboard.

Dartboards with steel tips: The diagonal distance is 9 feet 7 inches and 38 inches (2.93 meters).

Dartboards are frequently tipped: The diagonal distance is 9 feet 9 inches and 12 inches (2.98 meters).

Someone must maintain a measuring tape at the target for you to measure diagonally to the front of where the throw line should be for this one. You may use the Pro Line measuring tape, which lets you to use a dart to keep the dial gauge in position, for an easier means of assessing or if you don't have somebody to help you.

Also read: Bristle best dartboard - Overall Winner

How to Install a U-Shaped Bracket on a Dartboard

The Viper Wall Mounting Hanger Kit comes with instructions. These commands may be used on any sisal dartboard with a u-shaped metal mount. Most sisal dartboards come with U-shaped brackets as standard. For best stability, we suggest putting your dartboard straight into a stud. Use hefty duty anchors to withstand the strain of your dartboard if you're fixing it in drywall. Make sure you have all of the equipment needed before you begin. A drill or screwdriver, a pencil, and a tape measure are all necessary tools. Let's get this party started.

How to Display a Dartboard: Stage process Directions

Begin by drawing a line on your wall at the right height from the floor (5'8" or 1.73m). This is the height at which the bottom of the u-shaped channel should be. Using the Gimbal Nuts, attach the metal Mounting Feet to the rear of your dartboard. If your dartboard came with circular plastic Shims, nail each one into the back of the board using a mallet. Make a triangle form with them by spacing them equally. The Dartboard Center is a place where you may play darts. Screw into the pre-drilled hole, allowing enough room for the Growing Demand to hang the dartboard.

For further information on correct screwdriver depth, see our extra advice below:

Install the Mounting Bracket to your wall with the two Bracket Installing Screws, or wall anchors if not positioned above a stud.

Inspect the dartboard's tightness against the wall by placing it on the Growing Demand. Undo the Dartboard regulation Screw and straighten or remove it as appropriate if the dartboard is swaying.

Additional Suggestions for dartboard Installation

It might be difficult to get the center screw height on the dartboard set to the right depth. A detailed example is provided below to help you understand how much of the screw should be left hanging out of the rear of the dartboard. There won't be too much of the screw left to connect onto the bracket if it's twisted too deep into the dartboard.  If the screw isn't firmly screwed into the board (as seen in the second figure), it will latch onto the bracket but will be unsteady and off-balance. Lowering or raising the central screw until the dartboard no longer wobbles may take a few attempts.

How to install a quick fit Bracket on a Dartboard?

The quick-fit dartboard mounting bracket is a comparatively modern dartboard regulation option. To avoid uncertainty and wobbling, it employs a route slider mechanism. Essentially, this mounting approach speeds up and simplifies the operation. You won't have to worry about finding the perfect connection elevation or fiddling with installing runners.

Conclusion:

Dartboard regulation shows board for darts Height is 5 feet tall. The distance from the floor to the center of the bull's eye is 8 inches. The distance from the dartboard's front to the throwing line is Soft Tip: 8 feet 0 inches, Steel Tip: 7 feet 9 1/4 inches. Simple pieces of tape will be enough to designate the throw line. Major competitions, on the other hand, employ a "hockey," a thin elevated strip of wood about 1 1/2 inches high.

Share via email: